Buying Guide

How to price EV charging: per kWh, per hour, session and idle fees.

Per kWh, per hour, per session or an idle fee: what each one bills, where state weights and measures law allows kWh pricing, how to cover energy and demand charges, and when complimentary charging makes more sense.

Knowing how to price EV charging comes down to three questions: what the law lets you bill for, what each session really costs you, and what you want drivers to do once their car is full. Answer those three and the price nearly sets itself.

This guide is for commercial site hosts and charge point operators in the United States. It covers pricing models, where per-kWh billing is allowed, energy and demand costs, idle fees and complimentary charging. It is general information, not legal or tax advice.

The four building blocks of a charging price

Almost every public charging price is built from four parts, used alone or combined:

ModelWhat it billsWhere it fits
Per kWhEnergy delivered to the vehicleMost public sites, fast or slow
Per hour or minuteTime connected or time chargingParking-style charges, or where energy billing is not permitted
Per sessionA flat amount to start a sessionCovering fixed payment and network costs
Idle feeTime a car stays plugged in after charging endsBusy stalls where turnover matters

Per kWh is usually the fairest model for drivers, because two cars that take the same energy pay the same, whatever their charging speed. Time pricing charges a car that accepts power slowly more for the same energy, and drivers notice. A 2023 NIST review of the market describes time-based billing as a highly inconsistent indication of the quantity of energy delivered.

Where per-kWh billing is allowed

In the US, how you may sell electricity at a charger is set mainly by state weights and measures law. Most states build on two handbooks published by the National Institute of Standards and Technology (NIST):

  • NIST Handbook 130 sets the method of sale. It names the kilowatt-hour as the unit for electricity sold as vehicle fuel, priced on the energy actually delivered. The requirement first appeared in the 2013 edition.
  • NIST Handbook 44, Section 3.40 sets the device rules: accuracy, displays, receipts and price posting. It became a permanent code effective January 1, 2023. AC chargers carry an acceptance tolerance of 1% and a maintenance tolerance of 2%, and DC chargers are exempt from several requirements, including accuracy testing, until January 1, 2028.

Adoption and enforcement vary by state. The same NIST review found that 45 states had excluded public EV charging sites from the definition of a public utility. Two examples show the range:

  • California requires kWh pricing and type evaluation. AC chargers installed from January 1, 2021 and DC chargers installed from January 1, 2023 must comply when installed; older units have until January 1, 2031 (AC) and January 1, 2033 (DC).
  • New York states that electricity sold at retail as vehicle fuel shall only be sold by the kilowatt-hour, expects NTEP type approval, and requires owners to notify the state Bureau of Weights and Measures before a charger is used.
Before you post a per-kWh price Call your state weights and measures office, confirm which Handbook 44 edition it enforces, and ask your supplier for the type approval certificate your state requires for the exact charger model. Price display, receipt and registration rules follow from that answer. A note on MÖTEN hardware: our chargers do not yet hold NTEP or CTEP type approval. Where your state allows pricing by time or by session, and for fleet or private charging that does not bill drivers by energy, type approval is generally not required, and eMÖTEN CMS supports time and session pricing out of the box. In states such as California and New York that require kWh pricing for public charging, check with us before you plan per-kWh billing.

What else you can charge for

Electricity itself cannot be sold by elapsed time under the NIST framework, but NIST guidance allows an additional fee for occupying the space needed to connect, for overstaying after a full charge, or for other services tied to fueling, as long as the fee is properly disclosed. California requires time-based fees to be shown separately from the electricity and itemized on the receipt, and New York requires them to be posted before the customer buys.

Outside the US: a note on Canada

In Canada, electricity measurement is federal, under Measurement Canada and the Electricity and Gas Inspection Act. Time-based and flat-fee billing are allowed if the method is transparent and clearly shown to the driver at the time of the charge, and energy-based billing runs under temporary dispensations that remain in effect until December 31, 2029. Operators billing by energy must register as contractors under the Act.

Start from your real cost per kWh

Build the price up from the bill you will actually pay. Four lines matter:

  • Energy. The per-kWh rate on your commercial tariff, including any time-of-use periods.
  • Demand charges. Many commercial tariffs also bill your highest 15-minute average draw in the billing period. The federal Alternative Fuels Data Center (AFDC) notes that DC fast charging is more likely to trigger demand charges than Level 2.
  • Software, network and payment. Connectivity, card processing and any per-session platform fees.
  • Maintenance. The AFDC suggests estimating average maintenance costs of up to $400 a year per charger.

Demand charges are why lightly used fast chargers are expensive to run. An NREL analysis of more than 7,500 commercial and industrial electricity rates found the electricity cost of DC fast charging ranged from under $0.10 to over $2 per kWh depending on station design and use, and that cost falls quickly as utilization rises. Ask your utility about time-of-use rates, and check the rebates page for state and utility programs.

Two levers limit the exposure. eMÖTEN Power, the dynamic load management layer in eMÖTEN CMS, gives each circuit an amp budget, split in real time among the chargers actually drawing current and reassessed every 60 seconds, so the charging load has a known ceiling you can plan around instead of every port drawing at once. On DC sites with a thin service, the XEYAR battery-buffered architecture asks the grid for steady average power and uses an on-site battery to cover the peaks; the detail is on the Battery Buffered page.

A worked example (illustrative figures)

Suppose a Level 2 site pays 15 cents per kWh for energy, sees an average session of 20 kWh, and wants 3 cents per kWh for maintenance and network costs plus 5 cents for margin. The energy price is then 23 cents per kWh, or $4.60 for the average session, before card processing. For a public reference point, the Massachusetts Electric Vehicle Infrastructure Coordinating Council's public Level 2 guide gave an example range of $0.30 to $0.40 per kWh for 2024, built from local residential rates plus a modest increase, and warns that prices set too low can draw local drivers who would otherwise charge at home. The economics page covers the hardware side.

Idle fees: pricing the stall, not the electricity

Once a battery is full, a parked car blocks the next paying driver. An idle fee prices that. The same Massachusetts guide suggests:

  • Start the fee after the vehicle is fully charged, or after a preferred session length of 2 to 6 hours.
  • Allow a grace period of 15 to 30 minutes after charging ends.
  • Set it high enough to cover lost charging revenue and above any non-EV parking fee. Its 2024 example range was $3 to $12 per hour, typically 5 to 20 cents per minute.
  • Cap it daily, and post it clearly on signage.

Idle fees matter most where stalls are scarce, such as DC fast sites and busy retail lots; where cars are meant to stay overnight, they mostly irritate. Disclose the fee before the session starts and keep it on its own line on the receipt. In the eMÖTEN pricing engine an idle fee carries a grace period once a battery is full, and a timer model can switch to a per-minute rate after a set period.

Complimentary or paid: amenity charging

Not every charger needs to make money. The AFDC reports that more than 20% of public charging is offered to drivers at no cost.

Complimentary charging can also be simpler on the weights and measures side. California's code, for example, exempts equipment used solely to dispense energy where the amount dispensed does not affect customer charges. It still costs you energy and demand, though, so decide who it is for:

  • Everyone, as a pure amenity. Simple to run, but you pay for every kWh, and a posted time limit keeps long-stay cars turning over.
  • Guests, staff or tenants only. In eMÖTEN CMS, registered internal drivers such as staff and tenants charge with no billing at all, and issuing charging credit is how you decide who may charge at a site.
  • Hybrid. Complimentary for guests or customers, paid for the public, on the same charger. eMÖTEN Pay, the automated settlement layer in eMÖTEN CMS, classifies every session at the point of billing, so complimentary sessions are never counted as revenue and a paid session is never missed. Our hotel guide shows it on one property.

Setting the price in eMÖTEN CMS

The eMÖTEN CMS pricing engine prices by energy, time, session or any combination, and can vary prices by power band, site, charger, connector, postcode, driver or network. Drivers see the price before charging starts, get a receipt every time, and can pay by app, QR code, payment terminal, RFID or charging credit. The platform is a $0 CMS subscription on MÖTEN chargers and is available for the OCPP chargers you already own; plans and fees are on the eMÖTEN CMS page.

How the revenue settles with eMÖTEN Pay

A price is only as good as the money that reaches you. eMÖTEN Pay carries every paid session from the connector to the site owner's account:

  • Reconciled to the payment: each paid session is matched to its settled card payment. Declines, expired holds and refunds drop out, so nothing is paid out on a session that never cleared.
  • Card processing at exact cost: card fees are recovered at the exact amount charged on each specific payment, and there is no percentage of energy revenue.
  • Merchant of record: EVFastCharge is the merchant of record, so the site owner carries no card risk.
  • Monthly payout: driver payments are held in Stripe, not in our bank account. When the month closes, each site owner is paid from Stripe into their own Stripe Connect account and withdraws to their bank whenever they choose.

The full sequence, from holds and refunds to self-billed statements, is in our guide to automated settlement for EV charging.

A pricing checklist before launch

  1. Confirm your state's method-of-sale rule and the type approval your charger model needs.
  2. Pull twelve months of your tariff: energy rate, time-of-use periods and demand charge.
  3. Estimate average session energy and sessions per day per port.
  4. Build the per-kWh price from energy, demand, maintenance, network and margin.
  5. Decide whether a session fee, an idle fee or a time limit is needed, and post each one.
  6. Decide who charges at no cost, then review utilization and revenue after the first full month.

Frequently asked questions

Can I charge for EV charging by the kWh in my state?

In most states, yes, but the rules come from state weights and measures law. Many states follow NIST Handbook 130, which names the kilowatt-hour as the unit of sale, and NIST Handbook 44 Section 3.40, which sets the device requirements. Confirm with your state weights and measures office before you post a price.

Are idle fees allowed at EV chargers?

Under the NIST framework, a fee for overstaying after a full charge or for occupying the charging space is allowed as a separate charge for a service, as long as it is properly disclosed. Post it before the session starts and show it separately from the energy charge.

How do site owners get paid when drivers pay for charging?

With eMÖTEN Pay, each paid session is matched to its settled card payment. When the month closes, each site owner receives a line-by-line statement and is paid from Stripe into their own Stripe Connect account.

#Pricing #Idle Fees #Weights and Measures #eMÖTEN Pay

Set a price that covers the bill.

Send your tariff, charger count and how drivers use the site. Within two business days we will suggest a pricing structure and show how eMÖTEN Pay would settle it.